OmniVap XL Titanium

PRODUCT NUMBER: VOV 611-76-10-04

Product Characteristics

  • Midsection
    Titanium Stem
  • Condenser
    OMNI XL Condenser
  • Mouthpiece
    Omni / Titanium
  • Total Length
    109 mm

Product Description

At 109mm, the OmniVap XL Titanium includes the Titanium Tip, Cap, Omni Mouthpiece and XL Condenser Assembly, and a 62mm Omni Titanium Stem. Apart from the stainless steel cap, the OmniVap XL is made entirely of titanium and does not get hot even after prolonged use (except for vaporization chamber and titanium tip).

The Omni system has a specialized design to allow for simple adjustment of flow restriction, allowing complete control of the vapor and air intake ratio. Adjust by simply twisting the mouthpiece, which extends/retracts the condenser into the tip. It is not compatible with the M Tip or body midsections.
QUANTITY
-
+
$ 190.00
Use instructions
 
To use your VapCap:
  1. Most Important! Before your first use, please read all of these instructions and then do at least two, preferably more than two, dry runs with nothing in the VapCap! This is very important to become familiar with the operation of the unit and prevent unintentional combustion residues.
  2. The VapCap is unlike any other vaporizer, so give it a few tries empty to get the feel of its unique temperature-indicating click. Heat the VapCap in a quiet area, listen and feel so you know what you are looking for. If you are using a torch lighter, this should not take more than 5 or 6 seconds. Heat the middle of the cap not the end and rotate while heating. If more than 6 seconds go by and you don’t hear the click, stop heating and let it cool down.
  3. If you severely overheat your VapCap it can be permanently damaged. It is very important you hear the cool down click, or allow it to cool to the touch, before heating for the next cycle. Repeat this procedure several times to get the feel of how this little unit operates.
  4. When you are ready for the first use, let it cool down, then remove the cap from the VapCap.
  5. Fill the VapCap chamber with your material of choice. This can be done easily by pushing the VapCap into a container of your material and twisting. Pre-grinding your material is NOT needed like when using a bat or hitter. If you prefer to grind, go coarse. Finely ground material will get through the diffuser disc and into the unit.
  6. Place the cap back on the VapCap.
  7. Heat up the metal cap of your VapCap while rotating it, with the flame or heat source applied to the last third of the metal cap. Try to only apply heat to the side of the cap and NOT the end. This is not like lighting a smoking device.
  8. Continue rotating and heating the cap until you hear and or feel a click - this means the VapCap is ready!
  9. Puff on the mouthpiece. Experiment a little here. If you draw with the air hole completely plugged the flow will seem somewhat restricted. This is normal. Some find they get the best result by taking a long, slow steady draw with the hole completely open, and others will intermittently or lightly cover the air/vapor mix port. The way air flows through the VapCap cools the vapor to provide a smooth experience.
  10. Keep drawing as desired until you hear the click again, this means the VapCap has cooled down.
  11. When the vapor production diminishes, it is easy to reactivate. a. Make sure the VapCap has re-clicked “to cool” before reheating for the next cycle. b. If you are not sure if it has re-clicked, gently blow on the end to cool it. It may take up to 1 minute to reset.
  12. When there is no longer any desirable vapor produced, and the cap has clicked “to cool”, remove the cap. The consumed material can be either blown out the end, or the little tang on the cap is also a wonderful “digger outer.”
  13. Reload for another round of simple and wonderful vapor.
Tips:
  1. It is recommended that you use a butane torch style lighter with your VapCap.
  2. Wait until you hear or feel the reset click or at least 30 seconds after the VapCap stops producing vapor to reheat.
  3. It is VERY important to wait until you hear the cool down click before applying more heat.
  4. Stop heating your VapCap as soon as you hear the click until you get to know each other better.
  5. You can vary the intensity of the flavor by using the air/vapor adjustment port.
  6. Depending on your personal preference and heat source, as well as how many cycles since the VapCap was loaded, you may want to apply heat for 1-2 seconds after the click. This will provide for a different level of roasted flavor.
  7. DO NOT APPLY HEAT FOR MORE THAN 3 SECONDS PAST THE CLICK! OVERHEATING WILL PERMANENTLY DAMAGE THE VAPCAP!
  1. The end of the VapCap gets very hot during and following use. Do not touch the hot end until it has cooled. Also please do not put the hot end into your mouth.
  2. The VapCap can be safely put back in its Special Case or reloaded after the cool down click is heard.
We have done our best to remove the hassle from using a vaporizer. The VapCap doesn’t have any fancy digital display or lights, but it does make great vapor.
Cleaning instructions:
To remove consumed material from the chamber, either blow on the mouthpiece or use the built in extractor or “digger outer” to empty the chamber. The body can be cleaned with hot water. You can also use the included carrying case with almost any cleaning solution filled half full then shake or soak to wash your VapCap with the cap removed.
WARNING: Cleaning with alcohol or other flammable liquids is not recommended. Alcohol will not damage any component of the VapCap, even with prolonged soaking, but we do not recommend using it.
Dynavap compatibility chart
Condensers
(Sm = small, Lg = large)
Standard condenser
Standard condenser w/mouthpiece
Omni condenser assembly w/mouthpiece
M condenser
XL condenser w/mouthpiece
XL Omni condenser assembly w/mouthpiece
Devices
VapCap "M"
M Condenser, M Stem with built in Mouthpiece, SS Tip + Cap
OmniVap
Omni Condenser Assembly w/ Mouthpiece, Ti Body, Ti Tip + Cap
OmniVap XL
XL Omni Condenser Assembly w/ Mouthpiece, Stem, Ti Tip + Cap
NonaVonG-S
Standard Condenser, Mouthpiece, VonG Body, Ti Tip + Cap
NonaVonG
Standard Condenser, Mouthpiece, VonG Stem, Ti Tip + Cap
NonaVonG-XLS
XL Condenser, Mouthpiece, VonG Stem, Ti Tip + Cap
OmniVonG
Omni Condenser Assembly w/ Mouthpiece, VonG Body, Ti Tip + Cap
OmniVonG XL
XL Omni Condenser Assembly w/ Mouthpiece, VonG Stem, Ti Tip + Cap
OmniVap & OmniVap XL: Redesigned & Introduced
This is the Omnivap XL titanium
How strong is the OmniVap?

REVIEWS

DynaNews

Newsletter Signup

Sign up for our monthly newsletter and stay up to date on all DynaNews.

CONTACT

© 2018 DynaVap All Rights Reserved
HOME DYNASHOP DYNABUILDER VIDEOS FAQ ABOUT CONTACT